View and Download ABB ACS user manual online. ACS Inverter pdf manual download. MTAC pulse encoder interface module user’s manual 3AFE MUL1- R1 installation instructions for ACS, ACS,. ACS, ACS and. ACS Drives Users Manual ACS Three Phase Input. ABB ACS general machinery drives are designed for the OEM machine building sector.

Author: Mezishakar Shaktishicage
Country: Eritrea
Language: English (Spanish)
Genre: Life
Published (Last): 8 April 2016
Pages: 313
PDF File Size: 5.5 Mb
ePub File Size: 20.87 Mb
ISBN: 526-7-64112-605-8
Downloads: 22993
Price: Free* [*Free Regsitration Required]
Uploader: Mezijind

Fieldbus references are bipolar, i. The symbols are described below the table. Acs3350 and service inquiries Address any inquiries about the product to your local ABB representative, quoting the type code and serial number of the unit in question. TORQ is suitable for torque control applications. Timed functions A variety of drive functions can be time controlled, e.


Technical data What this chapter contains The chapter contains the technical specifications of the drive, e. Acs3550 the scalar control mode, the drive is controlled with a manaul reference. System overview The drive can be connected to an external control system via a fieldbus adapter or embedded fieldbus. Function Codes Function codes Supported function codes for the holding 4xxxx register are: The ID Run takes about one minute.

Set also deceleration time 2 parameter if two deceleration times will be used in the application.

mwnual The full set, partial parameter set application and mqnual sets can then be downloaded from the control panel to another drive or the same drive.

Installation checklist Checklist Check the mechanical and electrical installation of the drive before start-up. Ul Marking UL marking See the type designation label for the valid markings of your drive. The update time for the frequency input is 50 ms. It is also possible to activate jogging function 1 or 2 through fieldbus.


If the drive is operated in a critical part of a process, fan replacement is recommended once these symptoms start appearing. How to get help Step Action Display Press to read the context-sensitive help text for the item that is highlighted. Parameter values are the default values given in chapter Actual signals and parameters, starting acss350 page Delivery Check the label of your drive shows the valid markings Before installation The ACS may be installed on the wall or in a cabinet.

Amendment A1 Provisions for compliance: External Fault External Faults 1 and 2 can be supervised by defining one digital input as a source for an external fault indication signal.

Page Fieldbus control with embedded fieldbus What this chapter contains The chapter describes how the drive can be controlled by external devices over a communication network using embedded fieldbus. The user macro allows the user to save the parameter settings, including group 99 START-UP DATA, and the results of the motor identification into the permanent memory and recall the data at a later time. In Autotune Run, the speed controller is tuned based on the load and inertia of the motor and the machine.

Fuses must be used with other circuit breakers. Ignoring the safety instructions can cause injury or death.

Page Parameter download from source to destination Check that source and destination drive types drive has failed. Drive is programmed for traverse control with 30 sequences. FlashDrop is an optional device for fast copying of parameters to unpowered drives. Two units with the same address are not allowed on-line. Control Cable Ducts A diagram of the cable routing is shown below. With PTC the output current is 1.


Safety What this chapter contains The chapter contains the safety instructions which you must follow when installing, operating and servicing the drive. Thermal overload protection of the motor According to regulations, the motor must be protected against acd350 overload and the current must be switched off when overload is detected.

ABB ACS350 User Manual

Relion series cyber security deployment guidelie 62 pages. Start, stop, direction source for EXT1 The figure below shows the parameters that select the interface for start, stop, and direction for external control location EXT1.

For further information on environmental aspects and more detailed recycling instructions, please contact your local ABB distributor. The drive can continue the operation after the break if the main contactor remained closed. Direction lock is OFF. They must be removed and handled according to local regulations. Cooling Air Flow Requirements all digital inputs in the on state and the panel, fieldbus and fan in use.

Constant speed activation overrides the external speed reference. About control panels Use a control panel to control the ACS, read status data, and adjust parameters. Manyal coasts to stop. Scalar control It is possible to select scalar control as the motor control method instead of vector control.

The function is deactivated during emergency stop and jogging. The integration time defines the rate at which the controller output changes when the error value is constant.